Get it custom cut today for a better fit, light control and privacy.
Give your windows a beautifully clean look with new LEVOLOR Stock Premium Cordless Faux Wood Blinds. The innovative, easy lift cordless operating system allows you to smoothly raise or lower these blinds by simply lifting or lowering the bottom bar, and eliminates dangling cords for improved safety around children and pets.
Offers a clean look and increased safety for homes with children or pets.
Standard 2" slat gives windows a more shutter-like appearance.
Upgraded slat provides the look of real wood with increased durability and moisture resistance.
Elegant crown molding design for a perfect finishing touch.
No route hole design for increased light control and privacy.
* versus the competitor.
Premium construction is more durable than competitors’ plastic designs.
|LEVOLOR Premium Cordless Faux Wood||LEVOLOR Plantation 2" Faux Wood||Competitors Premium|
|Cordless Easy Lift Operating System||X|
|Consumer Preferred Valance||X|
|Consumer Preferred Wood Grain Texture||X|
|Larger Slat Size*||X||X|
|Decorative Wand Tilt||X|
|Durable Metal Headrail||X||X|
Measure exact distance to the nearest 1/8" between inside surfaces of window frame at the top, middle, and bottom, and use the narrowest width. Do not make any width deductions. Factory will make the appropriate deductions.
Measure exact distance to the nearest 1/8" from inside surface at top of window to sill at the left, middle and right and use the longest height. If you prefer blind not to touch sill, deduct 1/4". If there is no sill, measure height to point where blind is to reach.
|Standard Factory Adjustments From Ordered Width|
Measure exact distance to the nearest 1/8" between the outermost points where the blind is to be placed. For optimum light control, this measurement should extend 3/4" beyond the window opening on each side (or 1-1/2" for the entire width).
Measure exact distance to the nearest 1/8" from where top of blind will be located to top of sill. If there is no sill or if blind is to overlap window frame, measure to point blind is to reach.
|Allow Some Overlap|
For outside mount applications allow the blind to overlap 1-1/2" to 3" on the sides, top and bottom of the window.
You must add the overlap to your measurement; LEVOLOR does not add width or height for overlap on Outside Mounted blinds.
|Standard Factory Adjustments From Ordered Width|
|Blind Width||No adjustment||No adjustment|
|Valance||1" added||No adjustment|
NOTE: Whether you have a protruding or flush mount application is entirely dependent on the available depth of your window.
(Height x Depth)
(Side, Back or Top Mount)
Headrail Flush Mount
Valance Flush Mount
|1" Slat Size||1" x 1-1/2"||1/2"||1-3/4"||2-5/8"|
|2" Slat Size||1-1/2" x 2-1/4"||3/4"||2-1/2"||3-1/2"|
|2-1/2" Slat Size||1-1/2" x 2-1/4"||1-1/4"||3"||3-1/2"|
|Width||Up to 37 in.||37 in. to 47 in.||Greater than 47 in.|
|A. Box Bracket (Left and Right)||2||2||2|
|B. Support Bracket||0||1||1|
|C. Valance Clip||2||2||3|
|D. Bottomrail Endcap*||2||2||2|
|E. Hold-down Bracket**||2||2||2|
|F. #5 Screw x 3/4 in.**||4||4||4|
|G. #6 Screw x 1 1/4 in.||5||7||7|
*Not Required for Real Wood. **Not required for Real Wood or Cordless Faux Wood
Remove these parts packed in the headrail. Quantity varies with blind size.
Left Bracket / Right Bracket
Snap together where applicable.
IF APPLICABLE: Hold-down Brackets
The following are instructions to shorten LEVOLOR Stock Cordless Faux Wood Blinds.
Install and lower the blind fully.
Remove the end caps in the bottom rail (if already installed).
Slide out the slat in the bottom rail, exposing the inside of the rail.
Select the slat even with (or slightly below) the window sill; this will be the new bottom slat.
Below the bottom slat, cut all the horizontal connector cords (repeat for all horizontal connector cords below the new bottom slat)
NOTE: Be careful not to cut any vertical cords.
Trim off all loop cord below the new bottom slat (repeat for all loop cords below the new bottom slat).
Remove all excess slats below your new bottom slat.
Depress the lift button and slowly raise the bottom rail until it is touching the new bottom slat.
From the open bottom side of the bottom rail pull each of the ladder cords downward as far as they will go.
Cut the metal eyelets from the ladder cords.
Double check the desired length of the blind before any further cutting; then, trim all ladder cords 4 in. below the bottom rail.
Take the eyelets from the parts bag; working from inside the bottom rail, simultaneously thread both sides of the ladder cords through an eyelet (repeat for all ladder cords).
Slide the eyelets as far inside the bottom rail as possible and crimp tightly with the pliers (repeat for all ladder cords); trim excess ladder cord 2 in. below the eyelets.
Tie double knots below the eyelets for extra security.
Making sure all cords are tucked into the bottom rail, slide the bottom slat back into the bottom rail.
Finally, install the end caps.